November 18, 2026 - No. 46 In This Issue : Space Cargo Unlimited Eyes 2030 For REV1 Reentry Spacecraft Operations : More A380s Need Urgent Wing Spar Inspections, EASA Says : FRCE steps into the future with first C-130T induction at new Global TransPark facility : Boeing slide in 737 MAX deliveries hampers recent progress : What are the details of Boeing's new safety strategy focusing on the factory floor? : T-38C Lost Both Horizontal Stabilizers Before Crashing in Alabama, Investigation Finds : Aircraft Maintenance Under Remote Control : CFM Built A Jet Engine So Large That It Forced A Redesign Of The Jet It Powers : Inside The Boeing 737 MAX's Flight Control System : Boeing refines aerodynamic simulations using world’s most powerful open-science supercomputer Space Cargo Unlimited Eyes 2030 For REV1 Reentry Spacecraft Operations Share Robert Wall November 17, 2026 Space Cargo Unlimited's REV1 reusable reentry vehicle on display at Space Tech Expo in Bremen, Germany. Credit: Robert Wall/Aviation Week BREMEN, Germany—Space Cargo Unlimited plans to deploy its REV1 reentry space vehicle and associated elements in 2030. The REV1, being codeveloped with Thales Alenia Space, is due to carry the company’s BentoBox in-space manufacturing platform. The 3.7-metric-ton vehicle is designed to fly around 20 times, with the company looking to secure launch capacity for the missions, Chief Technology Officer Achim Schwarzwälder said. The system would provide slightly more than 1 metric ton of payload capacity, with 2.5 kW of continuous power. Space Cargo Unlimited has opted for a two-section setup for the spacecraft, comprising the REV1 reentry vehicle and an orbital module to provide power. The split reduces launch demand by reducing weight, though it would require the company to master on-orbit docking. The company is working with several potential suppliers but has not yet selected the eventual vendor, Schwarzwälder said. The orbital module, when not connected with the REV1, would operate as a node in a low-Earth-orbit communications constellation, he said. It would also provide high-bandwidth communications for REV1. An initial version of the BentoBox for research or manufacturing in microgravity is due to fly next year with ATMOS Space Cargo’s Phoenix 2 vehicle. A 1-metric-ton version is due to fly on a SpaceX Starfall reentry vehicle sometime in 2028 or after. The company says it is in talks with more than 150 potential customers, many in the life sciences and biotech sectors that have previously shown interest in microgravity work. “With BentoBox, we are developing the space factory that can fly across a fleet of vehicles,” CEO Nicolas Gaume said. More A380s Need Urgent Wing Spar Inspections, EASA Says Thierry Dubois November 17, 2026 Credit: Rob Finlayson LYON—The European Union Aviation Safety Agency (EASA) has published another airworthiness directive (AD) aimed at the wing spars on some Airbus A380s, this time expanding the number of aircraft that need urgent checks. The AD is the latest in a series that began in 2023 and later extended inspection requirements to the entire fleet, before making them more urgent and detailed on a limited number of aircraft. At issue is the structural integrity of the wing. As a starting point, a phenomenon called hydrogen embrittlement was identified as the cause of accelerated crack development in certain wing spars of A380s that had been stored for extended periods of time. Since the previous AD, released in June, EASA determined that eight additional aircraft may be affected by the same potential unsafe condition, hence the updated inspection requirements. In the new AD, EASA lists a total of 24 A380s—22 operated by Emirates, one by Etihad Airways and one by Qantas, according to Aviation Week Fleet Discovery. The new AD, effective Nov. 18, supersedes the June AD and is an interim action, EASA says. Depending on the serial number, checks must be conducted before the next flight, within 25 flight cycles or, for the eight additional aircraft, before Jan. 31, 2027. The inspections are focused on the wing mid spars. FRCE steps into the future with first C-130T induction at new Global TransPark facility 12 November 2026 From Rebecca McGann Hangar doors opened to a new milestone recently as Fleet Readiness Center East (FRCE) welcomed its first C-130T Hercules for scheduled maintenance, bringing the brand-new facility another step closer to full operational capacity. The induction kicks off the first full-scale maintenance, repair and overhaul (MRO) cycle on the airframe since FRCE was selected as the Navy's designated repair point for the C-130 fleet. Hangar doors opened to a new milestone recently as Fleet Readiness Center East (FRCE) welcomed its first C-130T Hercules for scheduled maintenance, bringing the brand-new facility another step closer to full operational capacity. The induction kicks off the first full-scale maintenance, repair and overhaul (MRO) cycle on the airframe since FRCE was selected as the Navy's designated repair point for the C-130 fleet. “The induction of our first C-130T Hercules represents more than the arrival of another aircraft. It marks an important step in expanding our capabilities and strengthening our ability to deliver readiness to the warfighter,” said FRCE Commanding Officer Col. Christopher C. McDonald II. “Establishing this heavy-aircraft maintenance capability required deliberate planning, disciplined execution and the collective efforts of an extraordinary workforce.” “This milestone reflects what we (Department of War, federal, state and local partners) can accomplish when our workforce, resources and priorities are aligned toward a common mission,” he continued. “I am proud of what this team has achieved, but more importantly, I am confident in what we will accomplish together. Our responsibility is not simply to build capability, but to turn that capability into results for the Fleet. This is how we strengthen readiness today while positioning ourselves to meet the demands of tomorrow.” Chris Melton, a C-130 Kinston branch head, noted that the aircraft was cleaned and stripped at Tinker Air Force Base, Oklahoma, before arriving at the new facility. However, future C-130s will not require this offsite step; FRCE expects its own state-of-the-art paint and strip capabilities at the complex to be operational by early 2027. “This is a true new beginning for us,” said Melton. “While we don’t know exactly what the future holds, this facility opens up incredible opportunities for long-term growth. The possibilities of what we can achieve here in Kinston are practically limitless.” Even though it only took three days from touchdown to the start of maintenance, this first induction represents the culmination of months of rigorous strategic planning, and three years of preparation since the depot was officially designated for the C-130 workload. Matt Sinsel, also a C-130 branch head at the facility, noted that as the team docked the aircraft, the overriding feeling on the hangar floor was one of immense excitement and pride for the mission they were launching. While this induction marks the start of full-scale planned maintenance intervals (PMIs) at the new facility, it builds upon a robust foundation already in place. FRCE personnel have honed their C-130 expertise by performing minor depot inspections (MDIs)—30-day, targeted depot evolutions that tackle structural repairs and corrosion beyond the scope of operational squadrons and intermediate-level maintainers. Alongside ongoing MDI work at MCAS Cherry Point, FRCE’s specialized travel teams continue deploying directly to flight lines across the globe, bringing depot-level service straight to the fleet. By pairing these expeditionary field teams with the heavy-maintenance throughput of the Kinston facility, FRCE now offers a comprehensive suite of depot-level sustainment capabilities for the C-130 platform. Transitioning from short-term field inspections to executing multi-month, full-scale overhauls required analyzing how other major depots managed the C-130 workload. To prepare for this massive expansion, FRCE planners studied established operations across the Air Force and commercial sectors. “Now, we have the opportunity to apply our own expertise and refine the process,” said Sinsel. “There is a deep sense of ownership and passion among our team to innovate and say, 'We can do it this way, and it's much better.' This milestone is a true team investment in making the program a success." That high level of technical expertise is vital for sustaining the platform. Often hailed as the workhorse of the military, the C-130T Hercules is a medium-sized tactical transport aircraft that supports global naval operations in some of the world's most demanding environments. Its versatile mission profile primarily includes tactical airlift, troop and cargo delivery, rapid emergency evacuations and vital humanitarian relief. Spanning approximately 75 acres, FRCE’s facility covers more than 700,000 square feet and has direct taxiway access to the North Carolina Global TransPark’s 11,500-foot runway, one of the longest civilian runways in Eastern North Carolina. It is projected to generate more than 350,000 direct artisan labor hours on the C-130 line by 2030. According to Sinsel, the program’s rapid ramp-up has already generated significant interest across the Navy, with several customers reaching out to inquire about sending additional aircraft to the site. He noted that this early demand reflects a broad recognition of the facility’s vast scale, cutting-edge capabilities and the exceptional caliber of its workforce. “The most significant impact of this facility is the long-term economic investment it brings to our local communities. That is how I define success,” Sinsel added. “Meeting our initial short-term goals is just the first step. The true mission is to secure two to three generations of steady, high-quality workload for Eastern North Carolina.” While the facility represents a historic economic win for the region, FRCE’s leadership emphasizes that the ultimate return on this investment will be measured by the combat power delivered to the flight line. “Our mission has never been simply about maintaining aircraft. It is about delivering the combat ready weapons systems our warfighters need to accomplish their mission at any clime and place when our nation calls,” said McDonald. “At FRC East, we are one team, one fight—united in purpose, relentless in focus, and disciplined in execution to deliver combat-ready aircraft to our warfighters, on time and on target.” FRCE is North Carolina's largest maintenance, repair, overhaul and technical services provider, with more than 3,800 civilian, military and contract workers. Its annual revenue exceeds $868 million. The depot provides service to the fleet while functioning as an integral part of the greater U.S. Navy; Naval Air Systems Command; and Commander, Fleet Readiness Centers. Boeing slide in 737 MAX deliveries hampers recent progress By Ian Molyneaux Edited By Emma Yates-Badley November 12, 2026, 05:48 CST Boeing Boeing saw a slide in its 737 MAX deliveries in October 2026, hampering recent progress made by the US planemaker following the summer months. On November 11, 2026, Boeing confirmed it delivered 49 aircraft in October 2026, a decrease from 57 deliveries in September 2026. In August 2026, Boeing delivered 51 aircraft and in July 2026, the company delivered 53. The company’s strongest month this year was in June when 64 planes reached customers. There was noticeable dip in MAX deliveries over October 2026, with only 32 aircraft making it out of the factory. In September 2026, the figure was 43 and in August 2026, 41. In September 2026, Boeing President and CEO Kelly Ortberg said that while 737 production is “now driving at 47 a month” it is not yet “stable” and it had taken a “little bit longer” than he had anticipated to increase from 42 to 47 aircraft a month. Ortberg also pointed to constraints in 737 wing production and that Boeing had “not seen the flow improvements that we expected in the time frame”. Dreamliner deliveries increased in October 2026, with 11 787s handed over to customers. However, the raised figure suggests Boeing was clearing a backlog rather than an acceleration in production. Among the airlines that received new aircraft were flydubai, Air New Zealand, Akasa Air and United Airlines. With two months of the year remaining, Boeing has so far delivered 524 aircraft in 2026. At the same stage in 2025, Boeing had delivered 493 planes and by the end of the year the total stood at 600. What are the details of Boeing's new safety strategy focusing on the factory floor? November 10, 2026 Boeing’s factory-floor safety and quality strategy centers on shifting from abstract data monitoring to direct, physical presence and open dialogue with assembly line workers. Driven by a federally mandated Safety Management System (SMS), the plan aims to eliminate defects at the source, empower frontline staff, and restructure manufacturing discipline. [1, 2, 3, 4, 5] The core tactical details of this factory-floor turnaround include: 1. Direct Floor Presence over "Dashboards" • Prioritizing Human Interaction: Boeing’s safety leadership explicitly warns against relying solely on data dashboards. They emphasize that critical safety risks and "hard information" surface first through face-to-face employee conversations on the floor. [1, 2] • Mandatory Factory Stand-Downs: Assembly lines utilize mandatory weekly safety stand-downs across factory stations to halt production and dedicate time strictly to safety and quality discussions. [1] 2. Workforce Training & Empowerment • Expanded Curriculum: Mechanics and quality inspectors receive over 300 additional hours of foundational coursework, utilizing digital training programs and hands-on modules. [1, 2, 3] • Protected Whistleblowing: The strategy heavily reinforces a "speak up" culture. Frontline workers are provided with confidential, protected reporting loops to escalate unresolved assembly defects without fear of workplace reprisal. [1, 2, 3] 3. Process Discipline & Defect Elimination • Eliminating "Traveled Work": The production sequence is strictly enforced, preventing incomplete or out-of-sequence jobs from moving down the line until they are fully approved and inspected. • State-of-the-Art Factory Tools: Teams are equipped with clearer digital production instructions, 3D-printed tools, and AI-driven verification systems to reduce assembly mistakes. • Early Defect Feedback Loops: Enhanced fuselage and end-of-line inspections give immediate, practical feedback to the mechanics, catching errors before aircraft leave the station. [1, 2, 3] 4. Real-Time Metric Tracking Boeing, under strict FAA oversight, continuously tracks key performance indicators (KPIs) tied directly to shop-floor health: [1, 2] • Workforce proficiency and training hours. • Rework hours and accumulated traveled work. • Supplier shortages and quality escapes. [1, 2] Would you like to explore how the FAA enforces its oversight with onsite inspectors on the floor, or look into the specific financial investments Boeing is making to support these factory updates? T-38C Lost Both Horizontal Stabilizers Before Crashing in Alabama, Investigation Finds Published on: November 6, 2026 at 10:35 PM CET Follow Us On Google News Stefano D'Urso A U.S. Air Force T-38 Talon aircraft assigned to the 14th Flying Training Wing, Columbus Air Force Base, approaches the runway for a landing during exercise Sentry South 26-2, Gulfport, Mississippi, Feb. 22, 2026. (Image credit: U.S. Air National Guard photo by Master Sgt. Rafael D. Rosa) SHARE A U.S. Air Force Accident Investigation Board determined that maintenance errors allowed a horizontal stabilizer actuator pin to become loose, triggering aerodynamic flutter that tore both stabilizers from the T-38C that crashed on May 12, 2026. The U.S. Air Force has released on Oct. 30, 2026, the results of its investigation into the May 12, 2026, crash of a T-38C Talon II assigned to Columbus Air Force Base, Mississippi. As we reported at the time, the aircraft crashed in rural Lamar County, Alabama, near the Mississippi border, after both pilots were able to eject safely. The Accident Investigation Board (AIB) found the chain of events that ultimately led to the crash started from a maintenance error. Because of the failure to secure and verify the connection, the left actuator’s aft attach pin backed out during flight, introducing mechanical play that catastrophically overloaded the torque tube and separated the horizontal stabilizer from the aircraft, says the AIB report. The investigation also identified multiple maintenance compliance failures that allowed the aircraft to return to flight without a required inspection. The training flight and the mishap The T-38C involved, serial number 66-4362 assigned to the 49th Fighter Training Squadron, was flying a fighter bomber fundamentals training sortie as part of the Introduction to Fighter Fundamentals (IFF) course. The crew included an instructor and an international student pilot, whose nationality was not disclosed. The aircraft was part of a larger four-ship formation, flying in the number 2 position. The first phase of the flight went smoothly, with the first issues emerging during the G-warmup maneuver. A T-38C Talon of the U.S. Air Force. (Image Credit: U.S. Air Force photo by MSgt Christopher Boitz) This maneuver, which usually includes two consecutive turns with increasing number of Gs, is used to prepare the pilots before they are subjected to high G-loads during training flights. In this case, the first was a 4G, 180-degree turn to the left. During the maneuver, the crew “heard a loud sound” and the aircraft started to shudder, followed by strong vibrations and negative Gs. The instructor immediately took control to stabilize the aircraft. However, the T-38 “produced a second, louder noise,” with substantially increased vibrations and an uncommanded pitch downwards with a spike in negative G. The instructor tried to use a full aft stick input to raise the nose back to level flight, without any effect. Considered the decreasing altitude, high airspeed, and inability to control the jet, the instructor gave the order to eject. “Severe aerodynamic forces caused the horizontal stabilizers to separate from the main fuselage, which then tumbled through the air,” said the report, and the T-38 “struck the ground in a flat, inverted (upside down) attitude, splitting in half upon impact.” A maintenance error The investigation traced the accident to maintenance work performed on the aircraft several weeks before the crash. In April 2026, the T-38C had previously been impounded following an uncommanded 130-degree roll to the right. A U.S. Air Force T-38C Talon assigned to the 49th Flying Training Squadron taxies to the runway on Columbus Air Force Base, Miss., Oct. 10, 2025. (Image Credit: U.S. Air Force photo by Airman 1st Class Kaylie Dille) During troubleshooting, maintenance personnel removed and reinstalled the aft fuselage, also known as the boattail, and found that the travel measurements on the right horizontal stabilizer’s trailing edge were outside the prescribed limits. After performing a backlash check on the right stabilizer, maintainers did not annotate defects. On the other side, the left horizontal stabilizer actuator servo arm was written-up for “excessive play.” The actuator was removed, repaired, and reinstalled, however the required backlash check was not annotated in the maintenance logs. In the end, the report says the right horizontal stabilizer rigging was accomplished and checked, correcting the out-of-limit travel, while the horizontal left stabilizer travel, system preload, and primary flight control checks were signed off as “good.” The T-38 was released from impound and completed a functional check flight on May 1 before returning operational. Investigators determined that the missing backlash check was a critical omission. The contractors who signed off the actuator installation, the work center supervisor, the Impoundment Official, Quality Assurance personnel and the Impoundment Release Authority all had the opportunity and capability to identify the missing inspection, but failed to do so. The horizontal stabilizers The horizontal stabilizers control the T-38’s pitch. Their actuators work against each other to apply tension to the torque tubes, helping prevent unwanted movement and aerodynamic flutter. An Air Force T-38 Talon taxis to an aircraft shelter at the Fleet Readiness Center Southeast (FRCSE). (Image Credit: U.S. Navy photo by Toiete Jackson) Investigators determined that an improperly secured pin in the left horizontal stabilizer actuator allowed excessive movement in the system. The resulting play, or backlash, disrupted the tension in the torque tubes and allowed aerodynamic flutter to develop and increase until the horizontal stabilizers separated from the aircraft. “The left torque tube snapped mid-air, causing both surfaces to depart the aircraft and land in separate geographic locations,” said the AIB report. “The left actuator and supporting structure tore free of the fuselage in flight, while the right actuator remained attached to the lower longeron support fitting.” The Air Force Research Laboratory and the Southwest Research Institute examined recovered components and confirmed one-time overload from axial and bending stresses with no fatigue present. “The torque tube failure was secondary,” described the report. “The loss of system rigidity resulting from a minor mechanical displacement (0.1”) at the left actuator’s aft attachment point was all that was required for catastrophic failure.” The pilots The Accident Investigation Board found no evidence that the crew contributed to the mishap. The instructor pilot attempted to regain control after the aircraft began experiencing severe vibrations and an uncommanded pitch-down movement. However, the separation of the horizontal stabilizers left the aircraft uncontrollable, leaving the crew without other options. Both pilots successfully ejected, although they had difficulties when maneuvering their parachutes, and both became caught in trees.. The instructor sustained a minor laceration to the face, but landed on his feet, according to the report. On the other hand, the student pilot “was suspended in a 1-meter-high bush, and had to drop approximately 12 inches to the ground,” and later “had difficulty walking due to severe pain in his left calf, causing him to limp. Aircraft Maintenance Under Remote Control When it comes to safety and maintenance efficiency, one key aspect is the ability to accurately diagnose and address aircraft faults. Understanding new technologies in aircraft system diagnosis methods and airplane fault detection techniques is crucial for ensuring reliable and safe operations. Remote technology encompasses a range of tools and methods that use video, audio, imaging, or communication systems to support maintenance or inspection activities performed from a location other than the immediate inspection area. Technologies currently used in aviation maintenance environments include robotic systems, augmented reality, virtual reality, remote visual inspection equipment, remote diagnostic systems, virtual maintenance technologies, and small unmanned aircraft systems (sUAS). Conducted in accordance with applicable regulations and approved procedures, remote technology can support maintenance and inspection activities by offering access to inspection areas that may be elevated, confined, or difficult to reach, improving inspection efficiency, supporting data collection, and facilitating communication between personnel. Going Remote Typically, general aviation (GA) operators don’t have the benefit of commercial airline budgets or massive corporate infrastructure. For private owners, flight schools, and small-scale maintenance shops, the focus shifts to cost-efficiency, accessibility, and local problem-solving owner-assisted maintenance. General aviation maintainers have technology options that give a high priority to compact, cost-effective hardware and software solutions, without sacrificing critical diagnostic power. Remote diagnostic systems may use sensors, predictive analytics, and data communication systems to monitor aircraft systems and support identification of maintenance conditions, system degradation, or potential failures. These systems may collect operational data, such as temperature, vibration, pressure, or system status, to support maintenance planning and troubleshooting. Virtual maintenance technologies may include augmented reality, virtual reality, and small drones to support maintenance troubleshooting, task guidance, and system visualization. Beyond the Wrench Rather than deploying complex, high-cost enterprise network architectures, general aviation operators are successfully implementing highly practical, consumer-grade technology platforms to achieve powerful results: • Augmented Reality (AR): Using tablets or lightweight smart glasses, technicians can overlay 3D wiring layouts and torque specifications directly onto physical hardware, keeping their hands free. AR also enables instant, real-time visual collaboration with off-site senior maintenance technicians to diagnose difficult faults. • Virtual Reality (VR): VR headsets replace the real world with fully interactive 3D simulations. Flight schools and maintenance teams use VR for risk-free, muscle-memory training and procedural familiarization on complex components without taking aircraft out of service. • sUAS/Drones: Lightweight commercial drones quickly perform rapid visual sweeps of elevated, hard-to-reach aircraft structures — such as vertical stabilizers, rudders, or upper fuselage and wing surfaces — greatly reducing the safety risks associated with ladders, stands, or scaffolding. The Regulatory Caveat & Hangar Practices While remote tools act as incredible capability multipliers, operators must align their usage with traditional safety and regulatory standards. The following hangar rules ensure safety remains paramount: • The Tactile Boundary: Remote technology is a supportive tool, but cannot replace physical presence when direct tactile assessment, manual manipulation (such as checking cable tension or control surface play), or non-destructive testing is required. If sensory checks are necessary under part 43, a qualified mechanic should perform the task. • Secure Hangar Connections: Broadcasting live audio and video feeds introduces potential cybersecurity vulnerabilities. Always protect your shop's network by applying basic Cybersecurity and Infrastructure Security Agency (CISA) guidelines, including enabling multi-factor authentication (MFA) and not reusing administrator credentials across tools. • Part 107 Drone Compliance: Any sUAS operations conducted around the hangar or ramp for aircraft inspection must comply with 14 CFR part 107. Drone pilots must be licensed, aircraft must be registered, and operations must strictly respect airport airspace boundaries and local flight guidelines. The use of remote technology is intended to support and enhance maintenance and inspection activities. Unless specifically authorized by applicable regulations, approved maintenance programs, or approved maintenance data, remote technology does not replace required inspection methods, maintenance procedures, or personnel qualifications. CFM Built A Jet Engine So Large That It Forced A Redesign Of The Jet It Powers Credit: Al.geba | Shutterstock, Simple Flying Add Simple Flying on Google Add as Preferred Source Follow on Google Discover By Luke Diaz Published Nov 12, 2026, 3:00 PM EST Luke Diaz is a freelance military writer with experience with active duty experience in the US Navy as well as defense and industrial engineering. He is a former Naval Flight Officer who performed tactical air control on the carrier-based E-2 Hawkeye. CFM International did not arbitrarily build an oversized engine. When Airbus announced the A320neo family featuring ultra-efficient, large-diameter engines, the CFM LEAP-1A and Pratt & Whitney GTF, airlines demanded a matching fuel-efficient option from the American maker. Boeing demanded a high-bypass turbofan to compete with Airbus, forcing the engine maker to deliver the LEAP-1B. Rather than spending years and billions of dollars building a clean-sheet, modern airplane from scratch, Boeing chose to modify the existing 737 Next Generation (NG) airframe. The original 1960s Boeing 737 was intentionally designed to sit very low to the ground. In the MAX, Boeing attempted to fit 2010s engine technology onto an airframe originally designed in the 1960s, in stark contrast to its competitor. While CFM actually shrunk the 737 MAX's engine fan to 69 inches (175 cm), compared to the 78-inch (198 cm) for Airbus, it was still far too large for the existing 737 airframe. Moving the heavy, wide engines upward and forward meant that during specific high-altitude, high-angle-of-attack maneuvers, the engine nacelles acted like mini-wings. To counteract the aerodynamics and ensure the MAX handled exactly like older 737 models, Boeing implemented the Maneuvering Characteristics Augmentation System software. MCAS was intended to operate in the background and autonomously push the nose back down, which ultimately became the focal point of the subsequent 737 MAX design crisis. America's Low-Slung Jetliner: Legacy And An Airframe Dilemma Credit: Wangkun Jia | Shutterstcok In April 1967, Boeing introduced the 737, which had a low fuselage and short landing gear for ease of ground crew access and was intended for tiny airports with minimal equipment needs. Pratt & Whitney JT8D engines, which fit neatly beneath the wing, were used in early variants. Wider fans were more cost-effective, but they also added weight and drag; thus, the need for greater fuel economy created problems. When Boeing began planning the 737-100 and -200 in 1964, the aviation world looked vastly different. Jet travel was transitioning to smaller cities, and the primary design objective was to build a self-sufficient aircraft. To pull off the ultimate trick of building virtually new planes while legally keeping them registered under the exact same 1967 type certificate, Boeing used a clever strategy for both the NG and the MAX. In the 1990s, Boeing engineered a larger modern wing, computer-controlled engines, and digital flight screens. However, to keep the planes operationally identical, engineers programmed those advanced digital screens to display retro, analog-style dials and preserved the mechanical overhead switch layout. Pilots could step into the advanced NG and fly it using the exact same muscle memory and procedures as the 1980s Classic models without setting foot in a simulator. The 2010s 737 MAX repeated this illusion but pushed it past physical limits. To fit massive, ultra-efficient LEAP-1B engines onto the low-slung frame, Boeing moved the engines higher and further forward on the wing. Boeing promised airlines that any pilot flying an NG could transition to a MAX by doing nothing more than an iPad course. To legally satisfy the Federal Aviation Administration (FAA) that the MAX was identical to the older 737 NG, Boeing had to present the new plane as having no major behavioral differences. The Hamster Pouch: Nacelle Cantilevers & Wing Geometry Credit: Coby Wayne | Shutterstock The 'hamster pouch' engine casing designed for the 1984 Boeing 737-300 is the exact mechanical ancestor of the MAX crisis. It represents the very first time Boeing chose to patch over a fundamental physical limitation with a clever, compromising workaround. When the Boeing 737-300 made its debut in February 1984 with the CFM56-3 engine mounted ahead of the wing, it represented a major engineering change. The engine's bypass ratio dropped from 24,000 to 20,000 pounds of thrust as a result of this move, which also produced a flat-bottom nacelle known as the hamster pouch and a smaller fan. The MAX initiative was started in 2011 as the need for fuel efficiency increased and the design's shortcomings became apparent. When airlines demanded efficient, wider turbofan engines in the 1980s, Boeing encountered the exact same obstacle they would face decades later: the 1960s fuselage sat too close to the ground. By the time the 2010s arrived, the required engines had grown so colossally large that flattening the bottom of the casing was no longer enough. Airbus gave CFM a massive 78-inch (198 cm) canvas for the A320neo because the A320 airframe sat high off the ground. Boeing, demanding the exact same thermodynamic efficiency, forced CFM to scale the LEAP engine down to a highly constrained fan for the MAX just so it wouldn't scrape the runway. To gain clearance, Boeing had to physically relocate the entire engine forward and upward, completely corrupting the airplane's aerodynamics and causing the nose to pitch up. Having run out of room for physical hardware workarounds like the hamster pouch engine housing shape, Boeing turned to a digital workaround instead. The severe, forward-cantilevered placement introduced intense physical loads on the wing structure and created the exact nose-up pitch characteristics that Boeing's MCAS software was secretly built to mask. How CFM Shrank The LEAP: Aerodynamic Side Effects Credit: Alexandr Zimovskoy | Shutterstock The A320neo's LEAP-1A engine, which has a bigger fan, taller landing gear, and a greater bypass ratio than the 737's rejected LEAP 1B, is an example of what CFM might have created with more space. Because it requires less thrust, the LEAP 1B has a redesigned low-pressure turbine construction, a lower bypass ratio, and less weight while maintaining the sophisticated core of its predecessor. After much discussion, Boeing decided to go with a bigger fan in order to increase efficiency. However, this choice created problems for the airframe, requiring the nacelles to be moved, which altered flight dynamics and potentially conflicted with federal stall regulation standards. CFM International upgraded the low-pressure turbine of the LEAP-1B engine from seven stages to five in order to lower the weight of the turbofan core in response to the strict design requirements of the MAX. In spite of the heavier engine housing of the CFM56-7B, developers used lightweight titanium alloys and ceramic matrix composites to improve thermodynamic efficiency. The prototype 737-8, which first flew on January 29, 2016, is powered by two LEAP-1B28 engines and demonstrated a significant reduction in fuel burn on medium-range flights. However, the reliance on software for engine integration linked to legacy flight controls laid the groundwork for future operational challenges and disruptions in commercial aviation. Where Boeing Found The Room: An Inflexible Airframe Credit: Coby Wayne | Shutterstock Three structural changes were made to the 737 MAX airframe by Boeing. The first modification was to lengthen the nose landing gear, which raises the engines and lifts the front of the aircraft, giving it a considerably higher nose than the NG model. Maintaining a certain minimum distance between the engine and the ground required this adjustment. There were fewer major changes to the wing box construction because the engines were positioned higher and farther forward on the wing. The engine housing's bottom was flattened to resemble the nacelle design from 1984, allowing for increased ground clearance. These changes have practical implications for ground personnel, as the hazard zone in front of each engine has expanded, affecting the safety of workers around the aircraft. Extensive flight testing was required to evaluate how moving the massive engines forward and upward altered the airflow dynamics surrounding the wings and nacelles. This physical displacement fundamentally disrupted the aircraft's aerodynamic stability, creating a distinct nose-up tendency that directly impacted how the jet handled and forced engineers to modify the flight controls. To address these handling deviations without embarking on a costly structural redesign, Boeing chose to fix the physical problem digitally. By embedding the Maneuvering Characteristics Augmentation System (MCAS) into the software, Boeing successfully satisfied regulatory handling criteria while preserving the single pilot type rating and avoiding catastrophic financial penalties tied to airline contracts. Inside The Boeing 737 MAX's Flight Control System How pilots fly the Boeing 737 MAX.2 By Daniel S Osipov Software Compensation: The Maneuvering Characteristics Augmentation System Credit: fikrizzudinoor | Shutterstock During flight tests, the 737 MAX engine configuration caused a slight nose-up tendency in various manual flying conditions. To address this, Boeing developed the MCAS to lower the nose when approaching such situations. Although the FAA and EASA later determined the airframe itself was inherently stable without it, Boeing chose to manage this hardware characteristic entirely through software, critically designing it to rely on a single, non-redundant Angle of Attack (AoA) sensor. This fragile design choice proved catastrophic. On October 29, 2018, a Lion Air 737 MAX 8 crashed into the Java Sea shortly after taking off from Jakarta, Indonesia, resulting in the deaths of all 189 passengers. Investigations revealed that a false high angle of attack reading activated the MCAS, causing the aircraft's nose to pitch down. Following this, Ethiopian Airlines Flight 302 also crashed in March 2019, leading to a total of 346 fatalities from both incidents, and the subsequent grounding of the MAX by regulators. Due to its technical issues, the 737 MAX was grounded for 20 months worldwide. While investigators picked apart the deadly relationship between the automated trim software and the plane's aerodynamics, Boeing's production lines ground to a halt. More than 400 undeliverable, newly built airframes sat stranded in desert storage lots, choking the supply chain and ultimately forcing the manufacturer to pay out over $8.3 billion in airline customer compensation. The crisis finally ebbed on November 18, 2020, when the FAA cleared the MAX to resume commercial service. The re-certification followed a complete overhaul of the flight control logic. MCAS now requires concurrent data from both AoA sensors, activates only once per aerodynamic event, and can be easily overridden by the flight crew. Boeing refines aerodynamic simulations using world’s most powerful open-science supercomputer By Ben Sampson 13th November 20264 Mins Read A Boeing simulation on Frontier shows turbulent airflow over an aircraft wing during landing. The close-ups show airflow along the wing’s leading edge progressing from (left) unstable flow to (center) turbulent bursts and then to (right) fully developed turbulence. (Image: Boeing, Jill Hemman/ORNL, U.S. Dept. of Energy) Boeing researchers have used Frontier, described by Oak Ridge National Laboratory as the world’s most powerful supercomputer for open science, to refine the aerodynamic simulations that predict how ice accumulation and turbulent airflow affect aircraft performance during take-off and landing. The work focused on high-lift aerodynamics, which covers the low-speed take-off and landing phases of flight. Higher-fidelity computational fluid dynamics (CFD) simulations run on Frontier helped to explain previously unexplained wind tunnel results for some high-lift wing designs, said the laboratory. The researchers said the simulations predicted the coefficient of lift to within 1%. According to the team, that accuracy provides the confidence needed to advance certain prototypes into production faster than before. Adam Clark, an aerodynamics engineer at Boeing, said, “Over the last 20 to 30 years, computer modeling has allowed us to go from having to perform 20-plus wind tunnel experiments on different wing variations to now just a couple. The goal isn’t to replace wind tunnels, but oftentimes, in physical testing, we see things that we can’t explain — things that we literally have no data for, and that’s what CFD simulations can shed a light on.” Frontier is an exascale system with a peak performance of two exaflops, or two quintillion calculations per second. Boeing gained access through the US Department of Energy’s INCITE Leadership Computing program and worked with specialists at the Oak Ridge Leadership Computing Facility to increase the speed and resolution of its simulations. Konrad Goc, an aerodynamics engineer at Boeing and co-investigator on the project, said, “Not only did Frontier allow us to run simulations that we couldn’t do before, but we were also able to get results in a matter of days, which would have taken months using a typical industrial-scale computing system.” Full-aircraft CFD has long relied on Reynolds-averaged Navier-Stokes equations, which model turbulence statistically, whereas wall-modeled large eddy simulation and direct numerical simulation resolve more of the turbulence at much greater computational cost. Clark said a full-scale wall-modeled simulation could take several months to produce a single solution on Boeing’s in-house system, whereas the team needs ensembles of solutions to be confident in its turbulence modeling code. The researchers used Frontier to study how wings respond to airflow when turbulence is modeled at full complexity and how ice accumulation affects wing performance in icing conditions. Clark said, “All of our airplanes are certified to operate safely in those conditions, and with Frontier, we were able to simulate flight through cold, icy clouds to understand how different ice shapes, sizes, and textures affect performance.” Because wing temperature influences how air moves over the surface, the simulations, which were accelerated by graphics processing units, also gave the team a new way to evaluate its anti-icing technology. The direct numerical simulations also examined laminar-to-turbulent transition and the effect of wall heating on a turbulent boundary layer, which Goc said cannot be observed in wind tunnels or during flight tests. Related findings on surface heating effects on attachment-line transition and relaminarization have been published in the Journal of Fluid Mechanics. Research by Boeing shows that a 1% reduction in drag in cruise conditions can lower fuel consumption on a flight by about 0.75%. The Frontier simulations are expected to guide aerodynamic design improvements and help mitigate issues found during flight testing. Source: https://www.olcf.ornl.gov/2026/11/10/aircraft-simulations-scale-new-heights-with-frontier-supercomputer/ Curt Lewis